Shenzhen FRIDA LCD Co., Ltd
Corporate mission: Promote smart AIOT and enable smart product applications. Corporate vision: Build a leading brand in AIOT field of audio and video solutions. Core values: To achieve customer first,
Add to Cart
11.6 Inch 1920x1080 Lcd All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE, the product content is TFT LCD Module, the Display size is 11.6 ", the Active area is 256.32(H) × 144.18 (V)mm, The Pixel Format is 1920(H) ×1080(V), the Pixel pitch is 0.1335(H) x 0.1335(V)mm, and the Pixel configuration is R, G, B vertical stripe.
Specifications:
| Parameter | Specification | Unit | Note |
| Display size | 11.6” (Diagonal) | inch | |
| Active area | 256.32(H) ×144 . 18(V) | mm | |
| Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel | |
| Pixel pitch | 0.1335(H) x 0.1335 (V) | mm | |
| Pixel configuration | R, G, B vertical stripe | ||
| Display mode | Normally black | ||
|
Surface treatment of front polarizer |
Anti-glare coating: (3H) |
Interface Connection:
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
| Pin No. | Symbol | I/O | Function | Remark |
| 1 | CABC_EN / NC | - | Reserved for CD | [Note1] |
| 2 | H_GND | P | High Speed round | [Note2] |
| 3 | Lane1_N | I | Complement Signal Link Lane 1 | |
| 4 | Lane1_P | I | True Signal Link Lane 1 | |
| 5 | H_GND | P | High Speed round | [Note2] |
| 6 | Lane0_N | I | Complement Signal Link Lane 0 | |
| 7 | Lane0_P | I | True Signal Link Lane 0 | |
| 8 | H_GND | P | High Speed round | [Note2] |
| 9 | AUX_CH_P | I | True Signal Auxiliary Channel | |
| 10 | AUX_CH_N | I | Complement Signal Auxiliary Channel | |
| 11 | H_GND | P | High Speed round | [Note2] |
| 12 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 13 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 14 | NC | I | Reserved for LCD manufacturer’s use | [Note1] |
| 15 | LCD_GND | P | LCD logic and driver ground | |
| 16 | LCD_GND | P | LCD logic and driver ground | |
| 17 | HPD | O | HPD signal pin | |
| 18 | LED-1 | P | Backlight ground | |
| 19 | LED-2 | P | Backlight ground | |
| 20 | LED-3 | P | Backlight ground | |
| 21 | LED-4 | P | Backlight ground | |
| 22 | BL_ENABLE | I | Backlight on/off | |
| 23 | BL_PWM_DIM | I | System PWM | |
| 24 | SCL/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 25 | SDA/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 26 | BL_PWR | P | Backlight power | |
| 27 | BL_PWR | P | Backlight power | |
| 28 | BL_PWR | P | Backlight power | |
| 29 | BL_PWR | P | Backlight power | |
| 30 | NC | - | Reserved for LCD manufacturer’s use | [Note1] |
[Note]:P: POWER I: Input O: Output
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
| Parameter | Symbol | Condition | Ratings | Unit | Remark | |
| MIN | MAX | |||||
| +3.3V supply voltage | VDD | Ta=25℃ | -0.3 | +3.6 | V | |
| Backlight supply voltage | VBL | Ta=25℃ | -0.3 | +21 | V | |
| Input voltage(eDP) | VI | Ta=25℃ | -0.3 | +1.5 | V | [Note1] |
| Input voltage(BL) | VBL_I | Ta=25℃ | -0.3 | VDD+0.3 | V | [Note2] |
| Storage temperature | Tstg | -10 | +60 | ℃ |
|
|
| Operation temperature | Topa | 0 | +50 | ℃ | ||
“Absolute Maximum Ratings” is regulations that do not exceed it even momentarily.
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
[Note1] eDP signals
[Note2]Backlight control signals (BL_ENABLE,BL_PWM_DIM)
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Supply voltage | VBL | 7.0 | 12.0 | 21.0 | V | |
|
Current dissipation |
IBL |
- |
(227) | (251) | mA | VBL=12V Duty Ratio=100% |
| (135) | (135) | mA | VBL=7.9V Duty Ratio=40% | |||
| Modulated light signal voltage | VPWM H | 1.85 | - | VDD | V | |
| VPWM L | 0 | - | 0.7 | V | ||
| Brightness Control Duty Ratio | Duty | 1 | - | 100 | % | [Note6-3-1] |
| Brightness Control pulse width | TPWM | 5 | - | - | ps | [Note6-3-2] |
| Brightness Control frequency | PWM | 200 | - | 2,000 | Hz | |
| LED-BL ON/OFF High voltage | VCNT H | 1.8 | 3.3 | 3.6 | V | [Note6-3-3] |
[Note6-3-1]Vpwm Input : 100%= Max luminance 1%= Min luminance
[Note6-3-2]The minimum value of the dimming signal pulse width is assumed regulations of the width of high and the width of low.
[Note6-3-3]VCNT Input : High = BL turn on, Low or OPEN =BL turn off
VBL-dip conditions
Optical Specification:
| Paramete | Conditions | Min. | Typ. | Max. | Unit | |
|
Viewing Angle(CR>10) |
Horizontal | L | - | 89 | - |
degree |
| R | - | 89 | - | |||
| Vertical | T | - | 89 | - | ||
| B | - | 89 | - | |||
| Contrast Ratio | Center | 700 | 1000 | - | - | |
| Response Time | Tr+Td | - | 25 | ms | ||
|
CF Color Chromaticity(CIE1931) |
Red x |
Typ. -0.05 |
TBD |
Typ. +0.05 |
- | |
| Red y | TBD | - | ||||
| Green x | TBD | - | ||||
| Green y | TBD | - | ||||
| Blue x | TBD | - | ||||
| Blue y | TBD | - | ||||
| White x | (0.313) | - | ||||
| White y | (0.329) | - | ||||
| NTSC ratio | % | (72) | - | |||
| Luminance of white | YLI | 220 | cd/m | |||
The measurement shall be taken 30 minutes after lighting the module at the following rating.
Condition: PWM Duty = 100%
The optical characteristics shall be measured in a dark room or equivalent.
Matters Needing Attention:
1.Be sure to turn off the power supply when inserting or disconnecting the cable.Please insert for too much stress not to join a connector in the case of insertion of a connector.
2.Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
3.Since the front polarizer is easily damaged, pay attention not to scratch it.
4.Wipe off water drop immediately. Long contact with water may cause discoloration or spots .
Reliability Test Items:
| No. | Test Item | Conditions |
| 1 | High temperature storage test | Ta=60℃ 72h |
| 2 | Low temperature storage test | Ta=-10℃ 72h |
| 3 |
High temperature & high humidity operation test |
Ta=40℃90%RH 72h (No condensation) |
| 4 | High temperature operation test | Ta=50℃ 72h |
| 5 | Low temperature operation test | Ta=0℃ 72h |
[Result Evaluation Criteria] Under the display quality test condition with normal operation state. Do not change these condition as such changes may affect practical display function.
[Normal operation state] temperature :+ 15~ +35C ,Humidity :45~75% ,Atmospheric pressure :86~106kPa